# Pastebin 5FsvCHru
tbot starting ...
├─Calling interactive_board ...
│   ├─kevin is on port 9907 and uses /dev/pts/32
│   ├─POWERON (kevin)
│   ├─Entering interactive shell (CTRL+D to exit) ...
Channel 0: LPDDR3, 933MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: LPDDR3, 933MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride

U-Boot SPL 2022.10-rc2-00116-g16448b5e19c (Aug 13 2022 - 19:02:03 -0600)
Creating new bloblist size 1000 at 100000
Trying to boot from SPI
Finished bloblist size 1000 at 100000
Found existing bloblist size 1000 at 100000
rockchip_rk3399_pinctrl pinctrl: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
rockchip_rk3399_pinctrl pinctrl: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
ns16550_serial serial@ff1a0000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19


U-Boot 2022.10-rc2-00116-g16448b5e19c (Aug 13 2022 - 19:02:03 -0600)

Model: Google Kevin
DRAM:  3.9 GiB
Core:  313 devices, 33 uclasses, devicetree: separate
MMC:   mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from MMC... fs_devread read outside partition 2
Failed to mount ext2 filesystem...
fs_devread read outside partition 2
Failed to mount ext2 filesystem...
fs_devread read outside partition 2
Failed to mount ext2 filesystem...
fs_devread read outside partition 2
Failed to mount ext2 filesystem...
*** Warning - bad CRC, using default environment

In:    cros-ec-keyb
Out:   vidconsole
Err:   vidconsole
Model: Google Kevin
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:c...
** Unable to read file ubootefi.var **
Failed to load EFI variables
BootOrder not defined
EFI boot manager: Cannot load any image
starting USB...
Bus usb@fe380000: ehci_generic usb@fe380000: Failed to get clocks (ret=-19)
Port not available.
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: ehci_generic usb@fe3c0000: Failed to get clocks (ret=-19)
Port not available.
Bus usb@fe3e0000: USB OHCI 1.0
Bus usb@fe800000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fe900000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe3a0000 for devices... 2 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 1 USB Device(s) found
scanning bus usb@fe800000 for devices... 1 USB Device(s) found
scanning bus usb@fe900000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
No ethernet found.
missing environment variable: pxeuuid
Retrieving file: pxelinux.cfg/00000000
No ethernet found.
Retrieving file: pxelinux.cfg/0000000
No ethernet found.
Retrieving file: pxelinux.cfg/000000
No ethernet found.
Retrieving file: pxelinux.cfg/00000
No ethernet found.
Retrieving file: pxelinux.cfg/0000
No ethernet found.
Retrieving file: pxelinux.cfg/000
No ethernet found.
Retrieving file: pxelinux.cfg/00
No ethernet found.
Retrieving file: pxelinux.cfg/0
No ethernet found.
Retrieving file: pxelinux.cfg/default-arm-rk3399-gru
No ethernet found.
Retrieving file: pxelinux.cfg/default-arm-rk3399
No ethernet found.
Retrieving file: pxelinux.cfg/default-arm
No ethernet found.
Retrieving file: pxelinux.cfg/default
No ethernet found.
Config file not found
No ethernet found.
No ethernet found.
SF: Detected gd25lq64c with page size 256 Bytes, erase size 4 KiB, total 8 MiB
Offset exceeds device limit
sf - SPI flash sub-system

Usage:
sf probe [[bus:]cs] [hz] [mode]	- init flash device on given SPI bus
				  and chip select
sf read addr offset|partition len	- read `len' bytes starting at
				          `offset' or from start of mtd
					  `partition'to memory at `addr'
sf write addr offset|partition len	- write `len' bytes from memory
				          at `addr' to flash at `offset'
					  or to start of mtd `partition'
sf erase offset|partition [+]len	- erase `len' bytes from `offset'
					  or from start of mtd `partition'
					 `+len' round up `len' to block size
sf update addr offset|partition len	- erase and write `len' bytes from memory
					  at `addr' to flash at `offset'
					  or to start of mtd `partition'
sf protect lock/unlock sector len	- protect/unprotect 'len' bytes starting
					  at address 'sector'
sf test offset len		- run a very basic destructive test
## Executing script at 00500000
Wrong image format for "source" command
SCRIPT FAILED: continuing...
=> 
│   ├─POWEROFF (kevin)
│   └─Done. (28.009s)